Syntho Glass

Cena: Zapraszamy do kontaktu z biurem

Syntho-Glass® is the originally, patented fiberglass pre-impregnated composite that is activated by salt or freshwater. Packaged in a hermetically sealed foil pouch, it is ready to use and does not require any measuring or mixing. This system, when used with the appropriate primary sealant, enables you to repair and reinforce virtually any diameter pipe in minutes. Syntho-Glass not only restores a pipe to its original psi rating, but actually can make the repair area stronger than the original pipe, reducing downtime, saving in parts and labor. With an initial cure time of only 30 minutes (75°F/24°C), Syntho-Glass is excellent on copper, steel, SS, PVC, FRP, clay, concrete, rubber, and more. It is safe to use, nontoxic, noncombustible, and odorless. Syntho-Glass is a versatile solution for industries where quick-action repair can be critical.

Description

Syntho-Glass® is the originally, patented fiberglass pre-impregnated composite that is activated by salt or freshwater. Packaged in a hermetically sealed foil pouch, it is ready to use and does not require any measuring or mixing. This system, when used with the appropriate primary sealant, enables you to repair and reinforce virtually any diameter pipe in minutes. Syntho-Glass not only restores a pipe to its original psi rating, but actually can make the repair area stronger than the original pipe, reducing downtime, saving in parts and labor. With an initial cure time of only 30 minutes (75°F/24°C), Syntho-Glass is excellent on copper, steel, SS, PVC, FRP, clay, concrete, rubber, and more. It is safe to use, nontoxic, noncombustible, and odorless. Syntho-Glass is a versatile solution for industries where quick-action repair can be critical.

Typical applications:

  • Impact protection
  • Emergency repair
  • Corroded pipes
  • Irregular pipe fittings
  • Force mains and gravity lines
  • Joint and tee repair
  • Underwater repair and splash zone

Benefits:

  • Ready to use
  • Effective, time-saving
  • No mixing and no mess
  • Sets rock hard in minutes

Technical Data

Physical properties

Working Time: 5 Minutes at 24°C
Set Time: 30 Minutes at 24°C
Resin Type: Water-activated polyurethane
Resin Application: Pre-impregnated
Service Temperature: od -45° to 121°C
Application Temperature: od 0° to 65°C
Pressure once cured w/primary sealant: Maks. 300 psi (20.6 bar)
Shelf Life: 24 Months with recommended storage

 

Mechanical properties

Test Method Result
Tensile Strength ASTM D638 36,000 psi (2482.1 bar)
Lap Shear Strength ASTM D5379 900 psi (62.05 bar)
Flexural Strength ASTM D790 26,100 psi (1799.53 bar)
Dielectric Strength ASTM D149 16,000 Woltów
Dielectric Strength ASTM G14/G62 123 ft. lb (167J)

 

Chemical Resistance

Solution tested Result
Sulfuric Acid 50% No effect
Hydrochloric Acid 50% No effect
Sodium Hydroxide Solution 20% No effect
Gasoline No effect
Toluene No effect
Xylene No effect
Mineral Spirits No effect
Distilled Water No effect

 

Temperature vs. Time

Average temperature Approx Work Time Return to servicetime
35°C 3 min. 23 min.
21 °C 8 min. 28 min.
16°C 10 min. 1 godz. 25 min.
10°C 14 min. 2 godz. 42 min.
6°C 17 min. 3 godz. 2 min.
2°C 20 min. 6 godz. 21 min.

Additional information

Packaging:

Product Roll Size
SG205 2″ x 5′ (5.08cm x 1.524m)
SG309 3″ x 9′ (7.62cm x 2.743m)
SG415 4″ x 15′ (10.16cm x 4.572m)
SG430 4″ x 30′ (10.16cm x 9.144m)
SG450 4″ x 50′ (10.16cm x 15.24m)
SG830 8″ x 30′ (20.32cm x 9.144m)
SG850 8″ x 50′ (20.32cm x 15.24m)

 

Surface preparation:

Surface preparation and profiling shall promote continuous intimate contact between the CFRP system and pipe by providing a clean, smooth, and circumferential surface. Surface preparation shall be in accordance with SSPC-SP1 “Solvent Cleaning” and SSPC-SP10 / NACE 2 “Near White Blast Cleaning” 1-3 mil surface roughness (25-75 microns). If an exist-ing coating is present, roughen to degloss. The composite repair system is a bond -critical composite repair system requiring a strong adhesive bond between the clean pipe and the composite system.

Installation:

Installation of the composite System shall be performed by NRI qualified applicators only. Surface preparation, mixing of epoxy, and installation of the system are to be in accordance with NRI’s composite Installation Guide, latest revision. Quality control inspection during and after installation of the composite system shall be performed per NRI’s Installation Validation Procedure: Quality Control Records, latest revision.

Storage conditions:

Store in a cool, shaded area at an ambient temperature of 35ºC.

Datasheets

Datasheet – Syntho Glass